The Effects of Mouthwashes on the Color Stability of Resin-Based Restorative Materials / Efecto de los enjuagues orales en la estabilidad del color de materiales restauradores a base de resina

Abstract: Objective: This study investigated the effects of three types of mouthwash on the color stability of three resin-based restorative materials (nanohybrid resin composite, sonic-activated bulk-fill material, and compomer). Materials and Methods: To this end, 120 cylindrical disc specimens were prepared and polished, after which they were incubated in distilled water for 24 hours for post-polymerization. The baseline color values of each specimen were measured with a spectrophotometer, then the specimens were randomly divided into four groups. Following immersion in the mouthwashes for 24 hours, the specimens were rinsed with distilled water and dried before the color measurement was repeated. The values of color change (ΔE₀₀) were subsequently calculated. A two-way analysis of variance and Duncan's post hoc multiple comparison tests were conducted to determine statistically significant differences among the restorative materials. Results: All samples showed discoloration after immersion, albeit some instances of discoloration were imperceptible. In this respect, a statistically significant difference was found among the restorative materials and mouthwashes (p<0.05). Imperceptible ΔE₀₀ values were derived on the nanohybrid resin composite and compomer, but perceptible and acceptable ΔE₀₀ values were detected on the sonic-activated bulk-fill materials (p<0.05). The clinically unacceptable discoloration was observed on the sonic-activated bulk-fill composite immersed in Listerine®. Conclusions: Clinicians should make recommendations based on the potential staining capacity of mouthwashes prescribed for daily use in restorative materials. In this way, the need for renewal of restorations due to discoloration could be avoided.

Resumen: Objetivo: Este estudio investigó los efectos de tres tipos de enjuague bucal en la estabilidad del color de tres materiales de restauración a base de resina (resina nanohíbrida, resina bulk-fill de activación sónica y compómero). Materiales y Métodos: Para ello se prepararon y pulieron 120 muestras de discos cilíndricos, después de lo cual se incubaron en agua destilada durante 24 horas pospolimerización. Los valores de color de base de cada muestra se midieron con un espectrofotómetro, después las muestras se dividieron aleatoriamente en cuatro grupos. Tras la inmersión en los enjuagues bucales durante 24 horas, los especímenes se enjuagaron con agua destilada y se secaron antes de repetir la medición del color. Posteriormente se calcularon los valores de cambio de color (ΔE₀₀). Se llevó a cabo un análisis bidireccional de la varianza y las pruebas de comparación múltiple post hoc de Duncan para determinar las diferencias estadísticamente significativas entre los materiales de restauración. Resultados: Todas las muestras mostraron decoloración después de la inmersión, aunque algunos casos esta fue imperceptible. Se encontró una diferencia estadísticamente significativa entre los materiales de restauración y los enjuagues bucales (p<0,05). Se obtuvieron valores imperceptibles de ΔE₀₀ en el compuesto de resina nanohíbrida y el compómero, pero se detectaron valores perceptibles y aceptables de ΔE₀₀ en la resina bulk-fill activada sónicamente (p<0,05). Se observó una decoloración clínicamente inaceptable en la resina bulk-fill activada sónicamente inmersa en Listerine®. Conclusiones: Los clínicos deben hacer recomendaciones basadas en la capacidad potencial de coloración de los enjuagues bucales prescritos para uso diario en los materiales de restauración. De esta manera, se podría evitar la necesidad de renovar las restauraciones debido a la decoloración.

Evaluation of mechanical properties of fluoride-releasing dental materials after multiple fluoride recharge/discharge application / Avaliação das propriedades mecânicas de materiais dentários liberadores de flúor após aplicação múltipla de recarga/descarga de flúor

This study aimed to determine the mechanical properties of fluoride-releasing dental materials after an accelerated fluoride recharge/discharge procedure. Two fluoride-releasing glass ionomer types of cement (Ketac Molar Easymix and IonoStar Molar), a resin-modified glass ionomer (Photac Fil Quick Aplicap), and two compomers (Compoglass F and Glasiosite) were used in this study. A total of 30 rectangular specimens and 30 disk specimens of each material were prepared and placed in distilled/deionized water (n = 5). The amount of fluoride released was analyzed from the materials for 7-day discharge, 1st recharge, 7-day discharge, 2nd recharge, and 7-day discharge, and 3rd recharge. The de/pre- and post-recharge fluoride release were measured using an ion chromatography for 24 days. The flexural strength and microhardness of each group were evaluated. The microhardness of all restorative materials showed no significant change (p > 0.05) over the experimental period. The flexural strength properties of the restorative materials did not change within the time of the study. The study showed that the fluoride release/uptake causes no effect on the mechanical and physical properties of dental materials.

Este estudo teve como objetivo determinar as propriedades mecânicas de materiais dentários liberadores de flúor após um procedimento acelerado de recarga/descarga de flúor. Dois tipos de cimento de ionômero de vidro liberador de flúor (Ketac Molar Easymix e IonoStar Molar), um ionômero de vidro modificado por resina (Photac Fil Quick Aplicap) e dois compômeros (Compoglass F e Glasiosite) foram utilizados neste estudo. Um total de 30 amostras retangulares e 30 amostras de disco de cada material foram preparadas e colocadas em água destilada/deionizada (n = 5). A quantidade de fluoreto liberado foi analisada a partir dos materiais para descarga em 7 dias, 1ª recarga, descarga em 7 dias, 2ª recarga e descarga em 7 dias e 3ª recarga. A liberação de fluoreto pré e pós-recarga foi medida usando uma cromatografia de íons por 24 dias. A resistência à flexão e a microdureza de cada grupo foram avaliadas. A microdureza de todos os materiais restauradores não apresentou alteração significativa (p > 0,05) durante o período experimental. As propriedades de resistência à flexão dos materiais restauradores não mudaram no período do estudo. O estudo mostrou que a liberação/captação de flúor não afeta as propriedades mecânicas e físicas dos materiais dentários.

The effect of different drinks on the color stability of different restorative materials after one month

OBJECTIVES: The aim of this study was to evaluate the effect of three different drinks on the color parameters of four different restorative materials. MATERIALS AND METHODS: Three different composites (Filtek Ultimate Universal Restorative, Filtek Ultimate Flowable, and Filtek Silorane, 3M ESPE) and a polyacid-modified composite resin material (Dyract XP, Dentsply DeTrey GmbH) were evaluated. Eighty-four disc-shaped specimens of 8 mm in diameter and 2 mm in thickness were prepared (n = 21 each). Color coordinates (L*a*b*, DeltaL*, Deltaa*, Deltab*, and DeltaE*) were measured using a VITA Easyshade Compact (VITA Zahnfabrik) after 24 hr of storage (baseline) and after 30 day of storage in three different beverages of black tea, Coca cola, or water (control) (n = 7). In each beverage, the specimens were stored three times a day, one hr each, for 30 day. The color changes (DeltaE) were calculated and were analyzed by Kruskal-Wallis and Dunn multiple comparison test. RESULTS: The color difference (DeltaE*) of the resin materials ranged between 1.31 and 15.28 after 30 day of immersion in the staining solutions. Dyract XP in Coca cola (15.28 +/- 2.61) and black tea (12.22 +/- 2.73) showed the highest mean DeltaE* value after 30 day, followed by Filtek Ultimate Universal Restorative (5.99 +/- 1.25) and Filtek Ultimate Flowable (4.71 +/- 1.40) in black tea (p < 0.05). CONCLUSIONS: The compomers displayed unacceptable color changes at the end of 30 day in all beverages. Among resin composites, the silorane based composite exhibited relatively good color stability than the others. Filtek Ultimate Universal Restorative and Filtek Flowable showed similar color changes in all beverages.

Effect of different topical fluoride applications on the surface roughness of a colored compomer

OBJECTIVE: The aim of this study was to evaluate the effect of neutral sodium fluoride (NNaF) gel and acidulated phosphate fluoride (APF) gel on the surface roughness of colored compomer (Twinky Star), conventional compomer (Compoglass F) and resin-modified glass-ionomer cement (RMGIC) (Photac-Fil). MATERIAL AND METHODS: A total of 45 standardized disc-shaped specimens were prepared for each material. After 24 h, finishing and polishing of specimens were done with aluminum oxide disc. Surface treatments with topical fluoride agents or distilled water (control) were performed four times, and interspersed with 8 pH cycles, simulating high cariogenic challenges. After the treatment, the surface roughness (Ra) was determined using a profilometer. In each group, specimens with Ra closest to the mean were examined with a scanning electron microscope (SEM) at ×1,000 and ×3,500 magnifications. Two-way ANOVA was used to evaluate Ra measurements, and the differences in Ra values between subgroups for each material and each topical applications were compared by Tukey's highly significant difference pairwise comparisons. RESULTS: No statistically significant difference in Ra between the Twinky Star and Compoglass F was found. However, Photac Fil showed significantly higher Ra than these materials after all surface treatments. There was a general trend of Ra increase from controls to NNaF and APF gels for all materials. SEM observations revealed that the surface micromorphology of Twinky-Star did not differ significantly from that of Compoglass F. CONCLUSION: Both the compomers and the RMGIC showed significantly higher surface roughness when subjected to APF gel application.

Habilidade de selamento de diferentes materiais restauradores adesivos / Sealing ability of different adhesive restorative materials

The purpose of this study was to evaluate the sealing ability of different adhesive restorative materials to bovine enamel and dentin. Ninety standard sauce-shaped Class V cavities with 3 mm of diameter × 2 mm of depth were prepared in the buccal and lingual faces of 45 bovine incisors. The gingival margin was located in dentin and the incisal margin in enamel. Teeth were randomly divided in 9 groups (n = 10) and restored with the following materials: fve fowable composites, one microflled composite, one microhybrid composite, one compomer; and one resin-modifed glass ionomer cement (RMGIC). The restorations were made based on the manufacturer's instructions for adhesive treatment and restorative procedure. After polishing, the teeth were thermocycled and immersed in 2% basic fuchsin for 24 hours. Teeth were, then, serially sectioned generating 3 slices of 1 mm that were observed in a stereomicroscope under × 40 magnifcation. The degree of dye leakage was recorded as follows: 0 - no leakage; 1 - leakage up to half the cavity; 2 - leakage in more than half of the cavity; 3 - extensive dye leakage, reaching the deepest portion of the cavity. Data was statistically analyzed using Kruskal-Wallis non-parametric test complemented with Bonferroni?s test when the difference between means was signifcant (alfa = 0,05). Extensive dye leakage was observed in dentin margins. The results were statistically higher than in enamel margins (Mann-Whitney U test (p < 0.001)). Compomer restorations produced the highest marginal sealing in dentin, differing from all other groups. The highest degree of dye leakage in enamel was produced by the microflled composite. The majority of the materials exhibited leakage-free margins in up to 70% of the specimens. Both, materials and substrate signifcantly infuenced the sealing ability.

O objetivo deste estudo foi avaliar o selamento marginal de materiais restauradores adesivos diferentes ao esmalte e à dentina bovina. Noventa cavidades Classe V, padronizadas na forma de pires, com 3 mm de diâmetro × 2 mm de profundidade foram preparadas nas superfícies vestibular e palatina de 45 incisivos bovinos, com margem gengival localizada em dentina e margem incisal em esmalte. Os dentes foram aleatoriamente divididos em 9 grupos (n = 10) e restaurados com os seguintes materiais: cinco resinas fow, uma resina composta microparticulada, uma resina composta microhíbrida, um compômero e um CIVMR. As restaurações foram confeccionadas com base nas instruções dos fabricantes para tratamento adesivo e procedimento restaurador. Depois do polimento, os dentes foram termociclados e imersos em fucsina básica a 2% por 24 horas. Os dentes foram seccionados seriadamente gerando 3 fatias de 1 mm que foram observadas em estereomicroscópio sob magnifcação de 40×. O grau de penetração do corante foi registrado conforme segue: 0 - sem infiltração; 1 - infiltração atingindo metade da cavidade; 2 - infiltração em mais da metade da cavidade; 3 - infiltração extensa, atingindo a porção mais profunda da cavidade. Os dados foram submetidos ao teste não paramétrico de Kruskal-Wallis complementado com o teste de Bonferroni quando a diferença entre as médias foi signifcante (alfa = 0,05). Infiltração extensa foi observada nas margens dentinárias. Os resultados foram estatisticamente superiores aos produzidos em margens em esmalte (Mann-Whitney U (p < 0,001)). Restaurações de compômero produziram o maior selamento marginal em dentina, diferindo de todos os outros grupos. O maior grau de infiltração do corante em esmalte foi produzido pela resina composta microparticulada. A maioria dos materiais apresentou margens livres de infiltração em até 70% dos espécimes. Ambos, materiais e substratos influenciaram signifcativamente no selamento das restaurações.

Influence of flowable materials on microleakage of nanofilled and hybrid Class II composite restorations with LED and QTH LCUs.

Background: Class II composite restorations are more frequently being placed with margins apical to the cementoenamel junction (CEJ) and margins within the dentin are prone to microleakage. Aims: This in vitro study was used to evaluate the influence of flowable composite and flowable compomer as gingival liner on microleakage in Class II composite restorations and compare a light-emitting diode (LED) unit with a quartz tungsten halogen (QTH) unit for light-activating composite resins. Materials and Methods: Mesioocclusal and distoocclusal Class II cavity preparations were made in 72 sound extracted premolars. The buccolingual width was 2.5 mm and the gingival margins of all the cavities were placed 1.0 mm apical to the CEJ. The boxes were prepared 1.5 mm deep axially, making 144 slot cavities. Teeth were randomly divided into the following two groups (n = 72): (I) Universal Filtek Supreme XT; Universal Filtek Supreme XT + Flwable Filtek XT and Universal Filtek Supreme XT + Dyract Flow and (II) Filtek Z250; Filtek Z250 + Flwable Filtek XT and Filtek Z250 + Dyract Flow. Flowable materials were injected into the gingival floor of the cavity to a thickness of 1.0 mm. Each increment was cured for 20 s. One-half of the subgroups in each group were cured with QTH and the other half with LED light curing units (LCUs). After 1 week of incubation at 37°C, the specimens were thermocycled (5-55°C, x1500), immersed in 0.5% basic fuchsine dye for 24 h and sectioned and microleakage was evaluated at the gingival margin by two examiners using a 0-3 score scale. The data were analyzed using the Kruskal-Wallis and Mann-Whitney U tests. Results: The groups utilizing flowable liners had significantly less microleakage (P < 0.05). No significant difference was identified between Universal Filtek Supreme XT and Filtek Z250 composites with and without flowable materials. There was no significant between utilizing flowable composite or flowable compomer and between each similar subgroup when polymerized with either the LED or the QTH LCUs. Conclusions: A layer of flowable materials at the gingival floor of Class II composite restorations may be recommended to improve the marginal seal of a restoration.

Avaliação da solubilidade e desintegração de cimentos de ionômero de vidro modificado por resina e compômeros em função de proteção superficial / Evaluation of the solubility and disintegration of resin modified glass ionomer cements and compomers using surface protection

O cimento de ionômero de vidro foi desenvolvido a partir da união de dois outros materiais, o cimento de silicato e o cimento policarboxilato de zinco. Mesmo com a evolução desses materiais, a propriedade solubilidade/desintegração ainda está pouco clara na literatura. O objetivo deste trabalho foi avaliar comparativamente a solubilidade e desintegração de cimentos de ionômero de vidro modificados por resina e de compômeros, bem como, a necessidade ou não de aplicação de agentes de proteção sobre suas superfícies. Os materiais utilizados foram: M1-Vitremer (3M Co.); M2-Fuji II LC (GCAmerica Inc.); M3-Dyract (Dentsply); e M4-Compoglass (Vivadent). Os agentes de proteção superficial utilizados foram: P1-Fluroshield (Dentsply) e P2-FinishingGloss (3M Co.). Estes materiais foram submetidos a testes de solubilidade e desintegração de acordo com a norma ISO 7489 de 1986. Aos resultados foram aplicadas transformações angulares e submetidos à análise de variância (p < 0,05) a dois critérios fixos e teste de homogeneidade. Os cimentos de ionômero de vidro modificados por resina e os compômeros apresentaram diferentes valores de solubilidade e desintegração. O menor valor foi obtido pelo Dyract, seguido pelo Fuji II LC e Compoglass com valores intermediários e Vitremer com o maior valor. Concluiu-se que os materiais submetidos à proteção superficial apresentaram menores valores de solubilidade e desintegração que os não protegidos; os agentes protetores, Finishing Gloss e Fluroshield mostraram-se eficazes para proteção superficial dos cimentos de ionômero de vidro modificados por resina e compômeros

The glass ionomer cement was developed from two other materials, the silicate cement and the zinc policarboxilate cement. Even though these materials have been enhanced since their creation, the solubility/disintegration properties are still not clear in the specific literature. This study main purpose was to evaluate the solubility and disintegration of resin modified glass ionomer cements as well as the necessity of using coating materials over their surface. M1-Vitremer (3M ESPE); M2-Fuji II LC (GCAmerica Inc.); M3-Dyract (Dentsply); and M4-Compoglass(Vivadent) were used in this study. The coating materials used were P1- Fluroshield (Dentsply) and P2-Finishing Gloss (3M ESPE). These materials underwent solubility and disintegration tests according to ISO 7489 policies from 1986. The results were submitted to angular transformations and variance analysis and homogeneity test suggesting: the resin modified glass ionomer cements and compomers showed different solubility and disintegration rates, Dyract < Fuji II LC = Compoglass < Vitremer; the resin modified glass ionomer cements and compomers submitted to the surface protection showed lower solubility and disintegration rates contrasted to the non-protected specimens; Finishing Gloss and Fluroshield demonstrated effective surface protection for resin modified glass ionomer cements and compomers

Avaliação da efetividade da fotoativação de dois materiais resinosos com diferentes fontes de luz, por meio da microdureza Knoop, resistência à compressão, resistência flexural e caracterização dos materiais / Evaluation of the effect of the light source on the photo polymerization of two resin material by the Knoop microhardness, compressive strength, flexural strength and material characterization

O objetivo deste trabalho foi avaliar o efeito de um diodo emissor de luz (LED) Smart Lite PS (Dentsply) e da lâmpada halógena convencional Curing Light XL 3000 (3M) na efetividade de polimerização do compômero Dyract Ap (Dentsply) e da resina composta TPH Spectrum (Dentsply) por meio de testes de microdureza Knoop, resistência à compressão e resistência flexural e caracterização dos materiais. Foram confeccionadas 100 amostras e divididas em 12 grupos de acordo com o teste aplicado, a luz de polimerização e o material utilizado. A lâmpada halógena convencional selecionada, Curing Light XL 3000 (3M), tinha intensidade de 470mW/cm2 e comprimento de onda entre 400 e 510nm; o LED Smart Lite PS (Dentsply) tinha intensidade de 950mW/cm2 e comprimento de onda entre 450 e 490nm. O tempo de fotopolimerização para cada incremento com 2mm de espessura foi de 40 s. para a lâmpada halógena convencional e 10 s. para o LED. Para os testes de microdureza Knoop foram confeccionadas 20 amostras numa matriz cilíndrica com 8,0mm de diâmetro e 2,0mm de altura. As leituras da microdureza foram realizadas nas superfícies superiores e inferiores das amostras utilizando um microdurômetro Micromet 2003, com uma carga de 50 gf por 15 s. Para o teste de resistência à compressão foram confeccionadas 40 amostras numa matriz cilíndrica com 4,0mm de diâmetro e 8,0mm de altura. A resistência foi medida na máquina de teste universal de ensaios Emic DL 10.000 com uma célula de carga 500Kgf e velocidade de carregamento de 0,5 mm/min. Para o teste de resistência flexural foram construídas 40 amostras numa matriz em forma de caixa com 25,0mm de comprimento, 2,0mm de altura e 2,0mm de largura. A resistência foi medida na máquina de teste universal de ensaios Emic DL 10.000 com uma célula de carga 50Kgf e velocidade de carregamento de 0,5 mm/min...

The goal of this work was to evaluate the effects of the blue light emitting diodes (LEDs) Smart Lite PS (Dentsply) and the conventional halogen lamp Curing Light XL 3000 (3M) on the polymerization effectiveness of the Dyract Ap compomer (Dentsply) and the TPH Spectrum composite resin (Dentsply) by the Knoop microhardness, compressive strength, flexural strength and material characterization tests. A hundred samples were prepared and divided into 12 groups according to the test applied, the polymerization light and the material. The conventional halogen lamp light had power of 470mW/cm² and wavelength between 400 and 510nm; the LED light had power of 950mW/cm² and wavelength between 450 and 490nm. The polymerization time for each material 2mm buildup was 40 seconds for the conventional halogen lamp and 10 seconds for LED. For the Knoop microhardness tests the 20 samples were cylinder shaped, 8mm diameter and 2mm height. The hardness was read in the upper and lower side of the samples by a micrometer (Micromet 2003), with 50 gf for 15 seconds. For the compressive strength test the 40 samples were cylinder shaped, 4mm diameter and 8mm height. The strength was measured in an universal testing machine Emic DL 10.000 with 500Kgf and cross-head speed of 0,5 mm/min. For the flexural strength test the 40 samples were box shaped, 25mm length, 2mm width and 2mm height. The strength was measured in an universal testing machine Emic DL 10.000 machine with 50Kgf and cross-head speed of 0,5 mm/min...

In vitro cytotoxicity of four kinds orthodontic band cements / 대한치과교정학회지

Orthodontic band cements are widely used in the fields of orthodontics, but they are commonly known as cytotoxic material. Within an oral cavity several ions and components are released from orthodontic band cements, thus causing inflammation or injury to the periodontal tissue. Therefore, it is very important to estimate the biocompatibility of orthodontic band cements. The purpose of this study was to assess the cytotoxic effect of orthodontic band cements to HGF cells. A zinc phosphate cement, a glass ionomer, a resin modified glass ionomer, and compomer were used to evaluate three cytotoxicity assays: cell proliferation assay, MTT assay, and agar ovelay assay. The results were as follows: 1. In the cell proliferation assay, GI > ZPC, RMGI, RMGI24, GI24 > compomer24, ZPC24, compomer > metal ring lined up in order of cytotoxicity. 2. In the MTT assay, GI > ZPC, RMGI > GI24 > ZPC24, compomer, metal ring, RMGI24, compomer24 lined up in order of cytotoxicity. 3. In the agar overlay test, GI > GI24, ZPC, ZPC24, RMGI > RMGI24, compomer, compomer24, metal ring lined up in order of cytotoxicity.

Measurements of shrinkage stress and reduction of inter-cuspal distance in maxillary premolars resulting from polymerization of composites and compomers / 대한치과보존학회지

The purpose of present study was to evaluate the polymerization shrinkage stress and cuspal deflection in maxillary premolars resulting from polymerization shrinkage of composites and compomers. Composites and compomers which were used in this study were as follows: Dyract AP, Z100, Surefil, Pyramid, Synergy Compact, Heliomolar, Heliomolar HB, and Compoglass F. For measuring of polymerization shrinkage stress, Stress measuring machine (R&B, Daejon, Korea) was used. One-way ANOVA analysis with Duncan's multiple comparison test were used to determine significant differences between the materials. For measuring of cuspal deflection of tooth, MOD cavities were prepared in 10 extracted maxillary premolars. And reduction of intercuspal distance was measured by strain measuring machine (R&B, Daejon, Korea) One-way ANOVA analysis with Turkey test were used to determine significant differences between the materials. Polymerization shrinkage stress is [Heliomolar, Z100, Pyramid 0.05).

Effects on the tissue reaction using compomer & Ketac Silver in the maxillary furcation in the beagle dogs / 대한치주과학회지

Procedures for treatment of molar furcation invasion defects range from open flap debridement, apically repositioned flap surgery, hemisection, tunneling or extraction, to regenerative therapies using bone grafting or guided tissue regenerative therapy, or a combination of both. Several clinical evaluations using regenerative techniques have reported the potential for osseous repair of treated furcation invasions. Regenerative treatment of maxillary molars are more difficult due to the multiple root anatomy and multiple furcation entrances therefore, purpose of this study was to evaluated histologically compomer and Ketac Silver as a barrier in the treatment of a bi-furcated maxillary premolar. Five adult beagle dogs were used in this experiment. With intrasulcular and crestal incision, mucoperiosteal flap was elevated. Following decortication with 1/2 high speed round bur, furcation defect was made on maxillary premolar. 2 month later one premolar was filled with compomer and the other premolar was filled with Ketac Silver. After 4, 8 weeks, the animals were sacrificed by vascular perfusion. Tissue block was excised including the tooth and prepared for light microscope with H-E staining. Results were as follows. 1. Compomer & Ketac Silver restoration were encapsulated fine connective tissue. 2. In 4 weeks, compomer & Ketac Silver restoration slightly infiltrated inflammatory cells but not disturb the new bone or new cementum formation. 3. In 8 weeks, compomer & Ketac Silver restoration were less infiltrated inflammatory cell and encapsulated fine connective tissue. 4. Therefore, compomer & Ketac Silver filling to the grade III maxillary furcations with multiple root anatomy and multiple furcation entrances is possible clinical method and this technique is useful method for maxillary furcation involvement but it is thought that periodic maintenace should be needed

Anticariogenci effect of compomer and RMGIC / 대한치과보존학회지

The first purpose of present study was to compare the anticariogenic effect of compomer, resin modified glass ionomer cement and composite (RMGIC). The second purpose was to evaluate the recently introduced methods, which use confocal scanning microscope, in detecting initial caries around restoration. 2x4x1.5mm cavities were prepared from the recently extracted 50 human teeth on the buccal or lingual surface. The prepared teeth were randomly devided into 5 groups and restored with each filling material. Group 1: Dyract AP, Group 2: compoglass F, Group 3: F2000, Group 4: Z100, Group 5:Fuji II LC. The teeth were stored for 30 days in the distilled water, then stored in the buffer solution for artificial caries development; pH 4.3, lactic acid 100 mM, calcium 16 mM, phosphate 8mM, sodium azide 3mM. Then, the samples were sectioned longitudinally and examined with confical scanning microscope. The results showed that the use of compomer and resin modified glass ionomer cement showed caries inhibition zone whereas the composite did not. There was no difference in the width of caries inhibition zone between compomers and RMGIC. The confocal scanning microscope was useful in detecting initial caries around restoration.

Experimental study of the effect of Carisolv in caries removal on dentin bonding interface / 实用口腔医学杂志

Objective: To study the effect of Carisolv in caries removal on dentin bonding surface.Methods:24 extracted third molars with moderate carious were randomly divided into four groups. Each cavity was split into two parts, one part was prepared by Carisolv and the other by high-speed bur. Then samples were processed as follows: samples in group A were not treated, those in group B were treated with 320 ml/L phosphoric acid, SEM was used to observe the morphology of dentin surface of the samples in group A and B. Samples in group C were restored with Dyract AP and those in group D with resin for the observation of the microstructure of dentin-filling bonding interfaces.Results:In group A, rough surface without obvious smear layer was exhibited and dentinal tubules were clearly open after Carisolv preparation; after bur preparation, dentin surfaces were covered with a thick smear layer and no opening of tubules was visible. In group B, after treatment with 320 ml/L phosphoric acid, the smear layer was removed and dentinal tubules were exposed after either Carisolv or bur preparation, but tube stoppers were visible in the samples prepared by bur. In group C, resin tags were observed only in the samples after Carisolv preparation. In group D,dentin surfaces and lengths of the resin tags did not show remarkable difference after Carisolv or bur preparation, but more lateral branch connection between resin tags appeared in the samples prepared by Carisolv than by bur.Conclusion:The dentin prepared by Carisolv favors bonding between dentin and resin/compomer and has the advantage of restoring with compomer.

A study on the radiopacity of cavity lining materials for posterior composite resin restoration / 대한구강악안면방사선학회지

PURPOSE: The aim of this study was to determine the relative radiopacities of cavity lining materials (Resin-modified Glass Ionomer cement, Compomer and Flowable resin) for posterior composite resin restoration. MATERIAL AND METHODS: Resin-modified glass ionomer cement (Fuji II LC, Vitrebond(TM)), Compomers (Dyract , Compoglass, F2000, Dyract(R) flow Compoglass Flow) and Flowable resins (Tetric(R) flow, Aeliteflo(TM) Revolution(TM)) were used. Five specimens of 5mm in diameter and 2mm thick were fabricated with each material. Human molars were horizontally sectioned 2mm thick to include both enamel and dentin. The radiopacities of enamel, dentin, cavity lining materials, aluminum step wedge were obtainded from conventional radiograph and NIH image program. RESULTS: All the tested lining materials showed levels of radiopacity the same as or greater than that of dentin. All compomer tested (Dyract(R), Compoglass, F2000, Dyract(R) flow, Compoglass Flow) and Vitrebond(TM), Tetric(R) flow were more radiopaque than enamel. The radiopacities of Fuji II LC and Revolution(TM) were between enamel and dentin and resin-modified glass ionomer cement, Compomer and Tetric(R) flow were greater than those of Revolution(TM), Aeliteflo(TM) or dentin. The level of radiopacity of the tested materials was variable; those with low radiopacity should be avoided in class II restorations, where a clear determination of recurrent caries by the examining clinician could be compromised. CONCLUSON: Clinician should be able to distinguish these cavity lining materials radiographically from recurrent decay, voids, gaps, or other defects that lead to clinical failure. Utilization of materials ranked more radiopaque than enamel would enable clinicians to distinguish the lining material from tooth structure.